Knowledge Base

Reports - Summary Report

Summary Report

The summary report is the most in depth report on Vantify CAFM and cuts your data into various tabs such as job groups, service providers and sites. This guide will explain each of these sections


The report overview



The report is divided into three areas, in yellow the filters which control the data that is show, in green the tabs, and in red the data itself. In blue you can also turn on percentages and export the data.


Part 1 – The filters


The filters control the data that is presented and to a degree the sections that are available.


Between dates – This specifies the timescale we are viewing in the report. It is set to the last 30 days by default.

Report on – KEY – this determines whether you are looking at reactive, planned or quotes. This is important.

Site – A simple site filter, you can only filter to one site at a time.

Location – Only applicable once you have selected a site, you can report on a specific location such as ground floor, externals, basement etc.

Site Group – Site Group is usually reserved for your client, but can have other uses.

Service Provider Group – Usually reserved for M&E, Cleaning, Fabric etc. But can have other uses.

Service Provider – a simple filter to choose the service provider.

Region – Filter your region as set within the system

Site Associate type – A very specific filter where you can choose a job role which then produces another box where you can specifically choose an individual. Useful if you’re a manager.

Core Client – similar to site group, a filter of your clients


Add as many filters as you want to cut the data up in various ways. You can’t break it.



Part 2 – The tabs


Each tab within the report cuts the data up in a slightly different way. Each tab is presented the same but shows different data:


Region – displays a list of your regions, if you don’t have regions set up this will be N/A and can be ignored.

Priority – a list of the priorities that have been used in the specified timeframe. Useful to see how many Emergency jobs were attended to on time.

Job Group – a handy list of all the job groups in your system and how many jobs have been assigned to them. Useful to see how many “too hot” jobs you’ve had for example.

Service Provider – a league table of your service providers – who is using it well who isn’t, and see how many jobs have been assigned to each one. Add the percentages on to see extremely valuable information.

Site Group – shows a list of the site groups within your system and how many jobs have been assigned to each.

Site – the list of your sites with the number of jobs assigned to each one. Useful for trend reporting to see which of your sites are engaged in using the platform, or which sites have more issues than others.

Service Provider Group – useful to see how many M&E, Fabric, Security etc jobs that have been assigned. NOTE – service providers can be placed in more than one group so there is no total line.


Quotes by site – it shows a summary of the quotes assigned to each site, with how many have been accepted, rejected, declined etc.

Quotes by SP – similar to the jobs view, it is a league table on each of your SPs and a summary of the quotes that have been assigned to them.


KPI – only applicable if you use the KPI module, it’s a simple list of service providers, how many KPI survey’s they’ve completed in this time and the average score.

KPI Groups – a very specific report showing how many KPI Surveys have been completed by service line – M&E, Fabric, Security, Cleaning etc.


Part 3 – The data


The data is formatted the same way for each of the sections below, however it is presented differently depending on which section you are viewing:


Jobs



The jobs section, for each of these tabs presents the data in the following way (we have show percentages toggled on here):



Total jobs – this is a complex calculation based on where the job completion due date or attendance due date falls between the specified range.


NOTE – we often get asked how this count is produced. 11 counts are being carried out here meaning the data is impossible to replicate using the job export as it is a combination of multiple statuses, including when jobs were due for attendance, due for completion, completed and attended and the combination of the above. This report is doing more than the job export offers.


Open Jobs - Of the count of Total Jobs, how many are still open. If you tick show percentages it’ll display it as a percentage.

Completed Jobs - Of the count of Total Jobs, how many are completed.

Missed jobs - Of the count of Total Jobs, how many have been marked as missed by the service provider.

Attended on time - Of the count of total jobs how many were attended on time

Completed - Of the count of total jobs how many were completed on time


Clicking the down arrow on one of the lines will present the breakdown of that line into statutory and non statutory.



Quotes




Total Quotes - A combination of the number of quotes that were due and submitted for the date range presented.

Of these, how many were accepted, declined or rejected.

Expired is a system setting which comes in to play x days after a quote was submitted and not actioned.


KPIs



A simple breakdown of how many KPIs were completed, and the average score of that number.


Export


Everything within this report can be exported, either by exporting the entire report at the top, or clicking on any of the green numbers and exporting the data it presents.




Related Guides

ELOGCAFM-N-84

ELOGCAFM-N-82



Vantify CAFM Support

For further assistance on anything covered in this guide or others, please contact the Vantify admin team on 01480 499740 or helpdesk.cafm@vantify.com.

This guide was created by Vantify's Product Team and reflects the latest updates as of the specified date. Please note that the information provided may evolve with future system updates or changes. Additionally, some details may vary based on your specific user permissions and account settings within Vantify.